How to match Antennas and RF Interconnects, to your design

The International Data Corporation IDC predicts that there will be over 30 billion connected devices by 2020; up from the 13 billion today. The majority of connected things will do so over wireless. Key to the wireless system are antennas and the interfacing RF interconnects. If chosen correctly, antennas lead to high performance wireless devices. However, when overlooked, it can lead to system bottlenecks and instability. When considering your antenna choice, there are four factors that should be considered and are addressed below. 1) What is the intended use? 2) Wireless standard or custom build? 3) Impedance matching 4) VSWR. 

 1) What is the intended use?

When choosing antennas, the questions that need to be answered are where and how the antenna will be used. If the applications require maximum range and signal strength, then an external antenna would be ideal. For all other applications an internal antenna can be used and tuned accordingly to section 2.

 2) Wireless standard or custom build?

Below are the wide array of wireless standards provided by Suntsu.

Our engineering team are also available to aid you with your inquiries about custom designs.

Frequency Ranges (MHz) Antenna Type Applications
Chip PCB Indoor Outdoor Patch NFC
13.4 - - - - - X NFC
(Near Field Communications)
13.56 - - - - - X
14.23 - - - - - X
433 X X - - - - ISM (Cellular)
433.05-434.79 X - - - - -
450 X - - - - -
470 X - - - - -
863-870 X X - - - -
902-928 X X - - - -
698-798 X X X X - - LTE Full Band (GSM/3G/2G)
704-960 - - X X - -
824-960 X X - X - -
1427.9-1575.42 - - X X - -
1710-2170 X X X X - -
1710-2690 - - X X - -
2300-2400 X X - X - -
2490-2690 X X X

X

- -
1575.42 X - - X X - GPS / Glonass
1650-1606 X - - - X -
824-960 X X - X - - GSM/3G
880-960 - - - X - -
1710-2170 X X - X - -
1880-1930 X - - - - - DECT
2400 - - - X - - WiFi / Bluetooth / HDMI / Dual Band
2400-2500 X X X X - -
4900-5900 - X - - - -
5000 - - - X - -
5150-5850 X - X - - -
5150-5900 - X - - - -

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3) Impedance matching

Successful impedance matching allows for maximum power transfer and minimum signal reflection from the load. Therefore, if the cable, connectors, and antenna all have matching impedance levels, they will be able to deliver the maximum power, resulting in better efficiency throughout the system.

External antenna = Antenna + RF Cable + Connector

PCB antenna = Antenna + Connector

Chip antenna = N/A (soldered directly on the board)

4)  VSWR

VSWR (Voltage Standing Wave Ratio) is a measurement of efficiency. It looks at how efficiently power is sent from a power source to the load. It can be measured with the calculation VMAX/VMIN where VMAX is Maximum Voltage and VMIN is Minimum Voltage. The lower the VSWR the more efficient the power distribution across the system. Although it is important for an antenna to have a low VSWR value, this becomes irrelevant if it is not matched to the rest of the system. A system operates at the speed and efficiency of its weakest link. Therefore, if the cable and connector do not have matching or lower VSWR ratings as the antenna, then the system will not operate at the antenna’s rated VSWR.

A combination of all these factors translate to a better performing and more balanced system.

View our standard antennas online Here or Contact us for further information.